![atlas lathe motor atlas lathe motor](https://3.bp.blogspot.com/-B7caOG9z138/WRP6rXMTKlI/AAAAAAABP1A/07mt_sFdNA0mu5j6rxb-ozNMKso8F7dgwCLcB/s1600/_original.jpg)
#ATLAS LATHE MOTOR UPDATE#
In this video i give an update on where I am with the lathe. I disassemble and clean the reversing gear box and explain how it works.Ītlas 10F Lathe - 09 - Updates, Thank You's and the Dark Side of the Moon In this video I remove the saddle and the leadscrew reversing gear box. In this video I cover some of the tooling I have got for the lathe, what I have completed so far and where I need to go to get everything up and running.Ītlas 10F Lathe - 08 - Removing the Direction Feed gear box and Saddle Apron assembly I discuss my bearing replacement choice and give recognition to some folks that help me along the way.Ītlas 10F Lathe - 07 - Stuff for the Lathe and Current Progress This video describes the assembly of the counter shaft of the Atlas 10F Lathe.
![atlas lathe motor atlas lathe motor](https://i.ebayimg.com/thumbs/images/g/MIQAAOSwU5ZgK~aM/s-l225.jpg)
That is if you are only concerned with running the machine and not restoring it to original.Ītlas 10F Lathe - 06 - Counter Shaft Assembly To me, this seems like a good modification. This video describes the modifications that were made to my 10F lathe by a previous owner. I decided to leave it there because I am much less than perfect and am a neophyte hobby machinist.Ītlas 10F Lathe - 05 - Counter Shaft Modifications I will annotate the video where I goofed. Please note that I made an error in how I performed this but later caught my mistake and corrected it. In this video I discuss how the back gears are disassembled and the process I went through to determine what size shims I needed between the Head stock castings and the back gear castings to set the proper clearance for the gears. You get it all, even my goofs!!!Ītlas 10F Lathe - 04 - Backgear Disassembly and Shim Calculation I talk about the installation as well as how the pulley, bull gear and drive gear interact with the back gears.
![atlas lathe motor atlas lathe motor](https://cdn3.volusion.com/hpruc.gvutw/v/vspfiles/photos/10117-3.jpg)
In this video I re-install the headstock spindle on the Atlas Lathe. In this video i remove the headstock spindle from the lathe to figure out why the pin on the bull gear will not engage.Ītlas 10F Lathe - 03 - Headstock Spindle Installation I will post more videos of this machine covering the setup and some of the repairs that need to be made.Ītlas 10F Lathe - 02 - Headstock Spindle Removal This isn't probably the best condition machine, but for the little money that I had, I am glad to have it. Having just recently bought an Atlas TH54 lathe, I thought I would give a quick walk through and talk a little bit about the machine. The Lathe Reconditioning / Cleaning / or Whatever it was that I done Atlas 10F Lathe - 01 - Introduction If you have some documentation relating to the Atlas Lathe that I am missing, please email me and and let me know as I would like to gather as much as possible and place them here. These documents are available on a number of sites on the Internet, but I thought it would be a nice repository for them nonetheless. At the bottom of the page I will make available the related documents I have found for the machine in the event that a new user does not want to round them all up. So hang out and follow along as I get Bertha back in running order and hopefully start making things with the machine.īelow are the videos I made while doing the work on the lathe. Notice I did not say restore the machine, although along the way she did get some new parts. This section of the website will detail what i done to recondition or fix the lathe. that sounds a lot like being married doesn't it?) Well the price was right and I could not pass it up for better or worse. The machine as I found it had no tooling and instead of a compound slide and cross slide had some sort of T slotted table. Joomla Updates, Upgrades and ExtensionsĪfter some searching on Craigslist and other sale ads I finally landed an Atlas Lathe.Importing Joomla in NetBeans as a Project.